In this article in the next paragraph you can discover lots of professional resources involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't precisely brain surgery, however it does call for strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the task can move rapidly; if you need to open up a wall to remove the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you set up a new tub in your restroom if you have actually currently acquired a brand-new tub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be attached to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water system and also examine all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the tub needs to wait until the bathtub has been utilized a minimum of when as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that article on Installing A Bathtub while doing a search on the internet. Sharing is good. Who knows, you might be helping someone out. Thank you for your time. Visit us again soon.
This Site